Getting Back To Basics:

Crew Organization for Spinnaker

Hoists, Jibes and Douses

by Ron LaNeve

J/35 Joumal Fall 1994

Many sailing articles have been written describing how to perform the perfect jibe or spinnaker set,but rarely do you read exactly what the specific tasks of each crew member are for those maneuvers. The details of each job may sound a bit basic, but this kind of organization is the key to performing your maneuvers well. As we all know, many mms are won, not by the fastest boat, but by the boat that makes the fewest mistakes. Having a plan, such as the one we suggest, should help to delegate responsibilities and avoid confusion. It is also valuable when organizing yournew crew for the next season or getting anew crew member acquainted with your system. The end result will be smoother maneuvers.

We hope this will mininize your mistakes,maximize your rewards and increase your fun factor in the J/35 Class!

The Hoist ... Standard bear-away set.

Bow Person:

1. Secure the spinnaker bag to rail.

2. Hook up sheet, guy and halyard on the final approach to the mark. Be certain that the spinnaker cannot be dragged out of the bag by a wave.

3. Help the spinnaker out of the bag on the hoist.

4. Take down the beadsail and have it ready to go back up at the leeward mark.

5. Clear off the foredeck, ASAP, and get ready for a jibe.

6. Get weight back on the rail.

Mast Person:

1. Raise the spinnaker pole at the mast end.

2. Hoist the spinnaker halyard on command from the cockpit.

3. Call out when the sail is to the top of the mast and cleated so the sail can be trimmed.

4. Back up the bow person in taking down the headsail.

5. Trim vang, ease outhaul, ease Cunningham as necessary.

6. Get weight back on the rail.

Pit Person:

1. Raise the spinnaker pole with the topping lift (working with the mast person).

2. Tail the spinnaker halyard going up.

3. Let the beadsail halyard down, not too fast so as to drop the sail into the water.

4. Prepare the spinnaker halyard for a takedown by flaking the halyard tad so it will run smooth and free.

5. Make sure the beadsail halyard is clear and ready to hoist.

6. And, if that is not enough, be ready to grind the spinnaker sheet or guy for the trimmers. This position is nicknamed "the hotbox" for a reason!

Mainsheet:

1. Ease the sheet keeping the sail full through the rounding.

2. Ease the backstay.

3. Trim (pump) the sheet as necessary, to give added speed and balance.

Sheet Trimmer:

1. Ease genoa sheet through rounding, approximately 5 feet.

2. Set up and trim spinnaker sheet. DO NOT trim the spinnaker until the halyard is all the way up. Your hoist will be faster and smoother this way.

3. Talk with the helmsman about sheet pressure and speed.

After Guy Trimmer:

1. Pre-sheet the guy on command. Don't be too anxious, as this can cause problems.

2. Trim spinnaker pole along with the sheet trimmer.

3. Control the foreguy. Keep the pole taught!

Helmsman:

1. Watch the mark.

2. Call the hoist.

3. Drive the boat for speed.

THE JIBE ... Standard Dip Pole Jibe

Bow Person:

1. Take lazy guy in hand to the pulpit and face aft, ready to insert the new guy into the jaw as the pole swings through the foretriangle.

2. Call "MADE" when the new guy is locked in the pole end.

Mast Person:

1. Trip the pole on command from the cockpit and swing the pole to the bow.

2. Help raise the pole once the guy is "made."

Pit Person:

1. Ease the pole down to the bow, quickly and smoothly. DO

NOT hit the bow person in the head! This might make him/her very upset and cause dissension.

the pole through the foot of the spinnaker.

Sheet Trinnner:

1. Stand in the cockpit with both sheets in hand, making sure they are both taughl It is OK to over trim a bit to help the boat stay in control during the jibe, especially in heavy air.

2. Fly the spinnaker without a pole for maybe 10 seconds or so while the pole is going to the opposite side.

3. Let go of the old sheet when the pole is "made." This will help the guy trimmer with his/her job.

After Guy Trimmer:

1. Stand behind or in front for the sheet trimmer, depending on your boat layout or you can use two people, one for each side of the boal Use whatever is most efficient

2. Square the pole to the wind, bring it aft as the boat slowly turns down wind. At the call for the trip, ease the guy to allow the sail to raise out of the jaws as the pole is dropped.

3.Release the old guy completely.

DO NOT pull the new guy until the bow person has secured it into the jaw of the pole so as not to pull the line out of his/her hands.

5. As the pole is going back up on the opposite side, pull the new spinnaker "tack" to the end of the spinnaker pole and resume trim on the new tack.

Mainsail:

1. Trim mainsail to centerline and hold it there.

2. Watch as the pole is going up on the opposite side, then ease the sail out again.

3. Triin for speed.

Helmsman:

1. Make sure spinnaker is full and drawing.

2. Steer the boat slowly and smoothly through the jibe, carving a nice mm.

3. It is better to take an extra few seconds to complete a clean jibe that to rush and have to untangle a twisted spinnaker.

4. Make sure all excess bodies are on the rail to balance the boat.

END FOR END JIBE

Mast Persons:

1. Stand in front of the mast.

2. On command, trip the pole from the masl

3. Bring the pole into the boat and release the old guy from thejaw. The sail is now free flying and the pole is floating across the boat.

4. Take the opposite sheetiguy and place it into the jaws of the pole. For a bigger boat, two people make this work a little easier and quicker.

5. Push the pole out to the clew of the spinnaker and attach the pole to the masl

Pit Person:

1. Ease the downhaul and the topping lift as needed by the foredeck crew.

2. Reset both for proper trim.

THE TAKEDOWN ... Standard Leeward Takedown

No matter what the conditions are, a successful takedown can be simple. There are many variations of takedowns but the one we

describe is straight forward, reliable, and ahnost foolproof.

Bow Person:

1. Open the forward hatch.

2. Have the lazy guy in your hand, under the headsail, ready to pull in when the spinnaker is released.

3. As you pull in the sail, it will come down and under the headsail. Stuff it directly into the forward hatch.

4. Disconnect the halyard, sheet and guy from the sail. Connect all three together, close the batch and get on the rail There will be time to clean up later.

Mast Person:

1. Hoist genoa on command.

2. Tighten outhaul, Cunningham, etc.

3. Back up the bow person as listed above.

4. Disconnect topping lift. Make sure headsail is clear to tack.

5. Get back on the rail ASAP.

Pit Person:

1. Tighten main halyard for upwind settings.

2. Tail jib halyard going up.

3. Ready the spinnaker halyard to come down. Totally release halyard on command. If done properly, the sail will invert and hang just above the water as the foredeck crew pulls the sail into the boat quickly.

4. Release the topping lift for the mast man. Once again, watch out for peoples' heads.

Sheet Trimmer:

1. Have genoa sheet ready to trim on a winch. Do not trim the headsafl as it may cause the spinnaker to collapse.

2. When the spinnaker halyard is released, let the spinnaker sheet go completely.

3. Trim the genoa for speed as necessary for the mark rounding.

After Guy Trimmer:

1. Ease the pole to the headstay on command.

2. Release the guy completely when the spinnaker is almost half way down.

3. Grind for the sheet trimmer.

4. Clear your winch for a tack.

Mainsail:

1. Tighten up the backstay.

2. Adjust the traveler and running backstays for upwind trim.

3. Trim the main for a powerful mark rounding.

Helmsman:

1. DRIVE THE BOAT! critical factor affecting the pointing ability and

2. Concentrate on a good, fast, tactical rounding. speed potential of the boat.

3. Do not over steer. Go for speed.

4. Communicate with your binuners for optimum speed.

Note: After you have the boat up to speed, one person should clean up and perpare the boat for the next mark rounding. The rest of the crew should be on the rail to balance the boat.

Typically, there are more crew members on board than we have listed tasks for. These extra bodies are not "rail meat;" they are the utility people to assist the others during the mark roundings as well as to watch for other boats, and to call waves and puffs. It is wise to have one person dedicated to oversee and organize each maneuver. This should be someone other than the helmsman or sail trimmers.

Communication prior to any mark rounding is key. Conversation on the rail should be about upcoming mark roundings and conditions on the race come. It is essential that you concentrate on doing your job 100% correct; do your job and not everyone else's at the same time ( the latter just spells disaster). By going bark to the basics and emphasizing the specifics of each maneuver, you can minimize your mistakes and maximize your rewards.

For further advice on these maneuvers for your particular boat, feel free to contact your local Shore Sails loft. We will be glad to help out in any way because knowledge is speed.

Ron LaNeve is a sail consultantfor Shore Sails, New Jersey.